top of page

Masonry Cleaning in the Right Order, So the Joints Survive the Wash

Ascent Surface Care
Nov 6
6 min read

It happens on brick buildings every year. A crew turns up with a high-pressure rig, the dark, blotchy wall comes up bright in an afternoon, and everyone is pleased until the next heavy rain. Then the staff in the corner office notice a damp patch on the inside wall. The jet had scoured the mortar back from the brick face and stripped the hard outer skin off the softer units, and the wall that used to shed water now drinks it. Masonry cleaning done that way turns a cosmetic job into a repointing project, and the damage, unlike the dirt, does not wash off.


None of that is inevitable. Brick and stone clean up beautifully when the work follows a sensible order, and each stage below exists to stop a specific mistake.

Name the Stain Before Anyone Picks a Method

What is on the wall decides how it should come off, and commercial masonry carries four main kinds of staining.


Green, black or gray patches, heaviest on north walls, under sills and copings and behind shrubs, are organic growth: algae, mold, mildew and lichen rooted into the porous surface. A white, powdery or crystalline bloom is efflorescence, salt left behind by moisture moving through the wall, which makes it a question about water before it is a question about cleaning. Dark, even deposits in sheltered spots, near busy roads and around exhausts and chimneys are soot and atmospheric grime, sometimes decades deep on older buildings. Orange-brown streaks under steel lintels, anchors, railings and lights are rust.


Each needs its own approach, so a bid that proposes one method for all four deserves a second look.

Open Joints and Spalled Faces Are Repair Work First

Cleaning improves how a wall looks. It cannot fix failing masonry, and washing a wall with open joints simply puts water where it should not be. Before anyone wets the brick, walk the building and look for:


  • Mortar recessed well behind the brick face, crumbling when scratched or missing altogether.

  • Cracks running through bricks or stepping up along the joints.

  • Spalling, where brick faces have flaked or popped off.

  • Loose or displaced units, bulges and leaning parapets.

  • Damp patches or interior leaks behind the stained area.


Any of these calls for a qualified mason or engineer. Urgent stabilization and leak repairs come before cleaning. Major repointing is often planned after a gentle clean, because a clean wall shows the true state of every joint and makes it far easier to match new mortar to the old.

A Test Patch Only Counts Once It Has Dried

Pick a small, representative area that takes in the brick, the mortar and any stone trim. If the building mixes brick types, or original and replacement units, each one gets its own patch.


Look at the result only once it has dried completely, since wet masonry hides color differences and residue. This is also the moment to agree on what "clean" means. Some staining is permanent, and older masonry should not be expected to look new. Settling on an achievable result up front stops anyone reaching for more pressure to chase the last shadow.

Glass, Trim and Shrubs Get Covered or Soaked Beforehand

Windows, painted trim, metal fixtures and sealant joints should be covered or shielded from solution and overspray. Shrubs along the base do best soaked with clean water first, so any drift is diluted, and rinsed again afterward.


Drainage gets planned at this stage too. On our projects, discharge is kept within local, state and EPA limits, and wash water can be recovered on sites where it should not reach storm drains.

Low Pressure From the Top Down Spares the Fired Face

Brick has a fired outer face that is harder and more weather-resistant than its core, and mortar is deliberately softer than the brick so the joint takes movement and moisture instead of the unit. Water pressure attacks both. The GSA's technical procedure for washing stone masonry warns that too much pressure wears away mortar joints and pushes water into the building, and that even low-pressure water becomes damaging once grit or an abrasive is added. Sandblasting and other abrasive methods are worse again, and preservation guidance generally rules them out for historic walls.


For organic growth and everyday grime, our exterior soft washing applies a biodegradable solution at low pressure, lets it break down the growth and soil, then rinses gently from the top of the wall down. Anyone wondering how to clean exterior brick on a single building or across a campus can borrow the same principle: use the gentlest treatment that moves the stain.


On masonry buildings from 3 to 15 stories, the wash goes up by drone while the crew stays below. With no lift on the lawn and no scaffolding tied to the wall, nothing can scrape a cornice or chip a brick edge. Porches, deep recesses and detailed entrances are finished from the ground, and a windy or wet forecast can move a flight day.

Rust and Soot Are Separate Jobs With Their Own Treatments

Rust streaks and heavy soot rarely respond to a general wash, and turning up the pressure to shift them is exactly how faces and joints get damaged. They need targeted, stain-specific treatments applied only where the stains are, and the corroding steel above a rust streak usually needs its own fix or the stain returns.


Nearby surfaces that genuinely need heat or force, such as a concrete plaza or a loading dock, can be scheduled for our hot water pressure washing, with the spray kept well clear of the masonry.

Soft Old Brick Needs a Soft Repointing Mortar

When the clean reveals tired joints, the repointing mortar matters as much as the cleaning method did. A hard, cement-rich modern mortar on soft old brick forces moisture and stress into the brick itself, which is why historic walls need a compatible mix chosen by someone who knows the material.


After that, light and regular beats heavy and rare. Most commercial brick and stone wants a gentle wash every one to three years, with shade, moisture and traffic deciding where a wall sits in that range, and the elevations where growth returns first setting the pace. Folding the masonry into the same visit as the windows and our other commercial exterior services saves a second mobilization, and both bundling and a recurring schedule earn a discount. The interval itself should still follow the wall.

Watch the Pavement at the Foot of the Wall

In its preservation brief on cleaning masonry, the National Park Service treats sand or stone grains turning up in the runoff as a sign the water pressure may be too high. Stand at the foot of the wall while it is being cleaned and look at what is running across the pavement. Dirty water is fine. Grit means the building itself is washing away, and the work should stop until the method changes.

Frequently Asked Questions

What should I ask when hiring brick cleaning services?

Ask which method and pressure they will use on the brick, how they will protect the mortar, whether they will clean a test area first and how they will handle runoff. Also ask whether any acid-based products are proposed and, if so, on which surfaces.

Is muriatic acid safe for cleaning brick?

It is rarely the right choice on an existing building. Strong acids can burn and discolor brick, attack mortar and ruin limestone or marble trim nearby. Acid cleaners are mainly a new-construction tool for removing mortar smears, used under the brick maker's guidance after careful testing.

Should brick be sealed after cleaning?

Not automatically. Many brick walls perform best with no sealer at all, and some film-forming products trap moisture and cause spalling. If water absorption is a genuine problem, a breathable water repellent can be considered once repairs are complete and a test area has been evaluated.

How do I know if a stain on brick is permanent?

A cleaned and fully dried test area is the best guide. Marks that survive a gentle, appropriate treatment may be in the brick itself, from old fires, past coatings or long weathering. Pushing harder at that point usually does the wall more harm than the stain.


Your brick and stone can come up clean and keep every joint it started with. Book a free consultation and appraisal with Ascent Surface Care, call our Austin team at (512) 400-7201 or our Oklahoma City team at (405) 673-1325, or email info@ascentsurfacecare.com. We respond to most inquiries within one business day.


Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
bottom of page